Please note: Installation of Campers & Dens must be conducted by a trained Champion through the Customer Experience Team.  Assembly Instructions support trained Champions for installation of Campers & Dens.  For assistance, please reach out to our Customer Experience Team.  

Below find the assembly instructions for Model B of Orangebox's Campers and Dens 

Downloadable version availible at the bottom of the page. 

Models: OB1CD02BLS / OB1CD02BRS
Orientation: LH shown (RH mirrored)
Assembly Document: Doc #168183 – Rev F (Jan 20, 2024)

⚠️ Safety & General Warnings

• For commercial use only
• Read all instructions before assembly or servicing
• This product must be properly grounded
• Isolate mains power before opening covers or servicing components
• The roof surface is not load bearing – do not place objects on the roof
• Do not block fan vents or grills
• Operating temperature range: 10–26°C (50–79°F)
• Relocation must be performed by Orangebox‑trained installers only

Risk of fire, injury, or electrical shock if instructions are not followed.

Electrical Use – Socket Restrictions

DO NOT plug any of the following into pod receptacles:

• Vacuum cleaners
• Heaters
• Air conditioning units
• Extension cords or power strips
• Other high‑amperage equipment

Only connect computer equipment and associated peripherals.

Before You Begin

• Confirm site clearance, ceiling height, and sprinkler conditions
• Ensure floor is level, clean, and capable of supporting pod weight
• Verify that all cartons share the same Order Number and Network ID
• For multi‑pod installs, ensure Network IDs match across all parts

Assembly directions, installation videos, and troubleshooting guides are available at:
https://ussupport.orangebox.com

Required Tools & Handling Notes

• No impact drivers
• Hand‑start all fasteners
• Torque wrench required (follow specified Nm values)
• Glass installation requires two or more installers
• Use appropriate PPE: gloves, safety glasses, safety footwear

High‑Level Assembly Sequence

Assembly must be completed in the order shown below:

1. Base Track Assembly
2. Service Hoop Assembly & Installation
3. Rear Frame Assembly
4. Front Frame Assembly & Wiring
5. Verify Square & Level Base
6. Acoustic Panel Assembly
7. Glass Unboxing & Installation
8. Door Assembly & Initial Alignment
9. Roof Assembly, Power‑Up & Alignment
10. Exterior & Interior Panels
11. Final Door Alignment
12. Trim Covers
13. Door Seal Installation
14. Optional Seismic Kit Assembly
15. Final Cleaning

Skipping or re‑ordering steps may result in misalignment, glass fit issues, or electrical faults.

Glass Handling – Critical Safety Notice

• Tempered glass is heavy and may shatter if mishandled
• Shipping crate must be tilted at least 5° before opening
• Remove protruding nails or screws before lifting glass
• Never impact edges or drag glass surfaces
• Always use two or more people

Improper glass handling can cause serious injury.

Door & Roof Adjustment Notes

• Door must remain parallel to the stopper
• Brush should barely contact the threshold
• Allow 30 seconds after powering the unit before roof operation
• Roof blade alignment must be verified in the fully closed position

Optional Seismic Kit

Seismic anchoring requirements are determined by the project’s Engineer of Record (EOR).

• EOR determines if anchoring is required
• Anchoring hardware is supplied by others
• Bracket hole diameter: 9.5 mm (0.374 in)
• Installation must comply with local building codes

Final Inspection & Cleaning

• Verify power, lighting, fan, roof, and door operation
• Confirm all panels and trim are securely installed
• Clean surfaces per Orangebox cleaning guidelines

Certifications & Compliance

• Conforms to UL 962
• Certified to CSA C22.2 No. 68
• FCC and IC compliant components

Reference

Orangebox Campers & Dens – Assembly Instructions
Doc #168183 – Revision F
© 2024 Steelcase Inc.

This Zendesk article is an installation overview and does not replace the official assembly manual.