Please note: Installation of Campers & Dens must be conducted by a trained Champion through the Customer Experience Team.  Assembly Instructions support trained Champions for installation of Campers & Dens.  For assistance, please reach out to our Customer Experience Team.  

Below find the assembly instructions for Model C of Orangebox's Campers & Dens 

Downloadable version availible at the bottom of the page. 

Models: OB1CD05CLS / OB1CD05CRS (LH shown, RH mirrored)
Document: 170488 – Revision B (Dec 20, 2024)

⚠️ IMPORTANT SAFETY & USE INFORMATION

• For commercial use only
• Read all instructions before installation
• This product must be properly grounded
• Isolate mains power before removing access panels or servicing components
• Roof surface is not load bearing – do not place objects on the roof
• Do not block fan vents or grills
• Operating temperature range: 10–26°C (50–79°F)
• Relocation must be performed by Orangebox‑trained installers only

Risk of fire, injury, or electrical shock if instructions are not followed.

Electrical Safety – Socket Use

DO NOT plug the following into pod socket receptacles:

• Vacuum cleaners
• Heaters
• Air conditioning units
• Extension cords or power strips
• Any high‑amperage equipment

Only connect computer equipment and associated peripherals.

Pre‑Installation Requirements

• Installation area must be level, clean, and capable of supporting pod weight
• Confirm ceiling height and sprinkler conditions with local AHJ
• Verify Product ID and Network ID labels match for multi‑pod installs
• Ensure all cartons match the same order number before assembly

Assembly instructions, installation videos, and troubleshooting guides are available at:
https://ussupport.orangebox.com

Required Tools & Handling Notes

• No impact drivers
• Hand‑start all fasteners
• Torque wrench required (refer to specified Nm values)
• Glass handling requires two or more installers
• Wear appropriate PPE: gloves, safety glasses, safety footwear

High‑Level Assembly Sequence

The Campers & Dens pod is assembled in the following major phases:

1. Base Track Assembly
2. Service Hoop Assembly & Installation
3. Rear Frame Assembly
4. Front Frame Assembly & Wiring
5. Verify Square & Level Base
6. Acoustic Panel Assembly
7. Glass Handling & Installation
8. Door Assembly & Alignment
9. Roof Assembly, Power‑Up & Alignment
10. Fascia & Exterior Panels
11. Final Door Alignment
12. Trim Covers & Door Seal
13. Optional Seismic Kit Installation
14. Final Cleaning

Each step must be completed in sequence. Skipping steps may cause misalignment, glass fit issues, or electrical faults.

Glass Handling – Critical Warnings

• Tempered glass is heavy and can shatter if mishandled
• Always tilt shipping crate at least 5° before opening
• Inspect crate for protruding nails or screws before removing glass
• Never impact or drag glass edges
• Use suction handles where applicable

Improper glass handling may result in serious injury.

Door & Roof Adjustment

• Door must remain parallel to the stopper
• Brush should barely contact the threshold
• Roof adjustments require opening the roof, adjusting linkage arms, then re‑verifying closure fit
• Wait at least 30 seconds after powering the unit before roof operation

Optional Seismic Kit

Seismic anchoring is optional and must be determined by the project’s Engineer of Record (EOR).

• EOR determines anchoring requirements and hardware
• Anchoring holes are 9.5 mm (0.374 in) diameter
• Product must be secured per EOR and local building code

Cleaning & Final Commissioning

• Complete cleaning after all panels and trim are installed
• Verify door, roof, lighting, fan, and controls operate correctly
• Confirm electrical grounding and power routing

Certifications & Compliance

• Conforms to UL 962
• Certified to CSA C22.2 #68
• FCC & IC compliant components

Reference

Orangebox Campers & Dens Assembly Instructions
Doc #170488 – Revision B
© 2024 Steelcase Inc.

This Zendesk article serves as an installation overview only and does not replace the official assembly manual.