Please note: Installation of Campers & Dens must be conducted by a trained Champion through the Customer Experience Team.  Assembly Instructions support trained Champions for installation of Campers & Dens.  For assistance, please reach out to our Customer Experience Team.  

Below find the assembly instructions for Model D of Orangebox's Campers and Dens 

Downloadable version availible at the bottom of the page. 

Models: OB1CD05DLS / OB1CD05DRS
Orientation: LH shown (RH mirrored)
Assembly Document: Doc #170491 – Revision B (Dec 20, 2024)

⚠️ Safety & Use Warnings

• For commercial use only
• Read all instructions before assembly and operation
• This product must be properly grounded
• Isolate mains power before opening covers or servicing components
• The roof surface is not load bearing
• Do not drill holes in or hang items from the pod
• Do not block fan vents or grills
• Operating temperature range: 10–26°C (50–79°F)
• Relocation must be completed by Orangebox‑trained installers only

Risk of fire, injury, or electrical shock if instructions are not followed.

Electrical Use – Receptacle Restrictions

DO NOT connect any of the following to pod socket outlets:

• Vacuum cleaners
• Heaters
• Air conditioning units
• Extension cords or power strips
• Any high‑amperage equipment

Only computer equipment and associated peripherals may be connected.

Before You Begin

• Confirm floor is level, clean, and capable of supporting pod weight
• Verify ceiling height and sprinkler conditions with local AHJ
• Check that all cartons match the same Order Number
• For multi‑pod installs, verify all Network ID labels match

Assembly directions, installation videos, and troubleshooting guides are available at:
https://ussupport.orangebox.com

Required Tools & Installer Notes

• No impact drivers permitted
• Hand‑start all fasteners
• Torque wrench required (refer to specified Nm values)
• Glass handling requires two or more installers
• PPE required: safety glasses, gloves, safety footwear

High‑Level Assembly Sequence

Follow the assembly steps in the order listed below:

1. Base Track Assembly
2. Service Hoop Assembly & Installation
3. Rear Frame Assembly
4. Front Frame Assembly & Wiring
5. Verify Square & Level Base
6. Acoustic Panel Assembly
7. Glass Unboxing & Installation
8. Door Assembly & Initial Alignment
9. Roof Assembly, Power‑Up & Alignment
10. Fascia & Exterior Panels
11. Interior Panels
12. Final Door Alignment
13. Trim Covers
14. Door Seal Installation
15. Optional Seismic Kit Assembly
16. Final Cleaning & Inspection

Skipping or reordering steps may result in misalignment, glass fit issues, or electrical faults.

Glass Handling – Critical Safety Notice

• Shipping crates must be tilted at least 5° before opening
• Remove protruding nails or screws before lifting glass
• Tempered glass is heavy and may shatter if mishandled
• Never impact glass edges or drag glass surfaces
• Use two or more installers at all times

Improper handling may cause serious injury.

Door & Roof Adjustment Guidance

• Door must remain parallel to the stopper
• Brush should barely contact the threshold
• Allow 30 seconds after powering before roof operation
• Verify roof blade alignment in the fully closed position

Optional Seismic Kit

Seismic anchoring requirements are determined by the project’s Engineer of Record (EOR).

• EOR determines anchoring necessity and hardware
• Anchoring holes are 9.5 mm (0.374 in) diameter
• Installation must comply with local building codes

Final Inspection & Cleaning

• Confirm lighting, fan, roof, and door operation
• Verify all panels, trim, and seals are secure
• Clean all surfaces per Orangebox cleaning guidelines

Certifications & Compliance

• Conforms to UL 962
• Certified to CSA C22.2 No. 68
• FCC & IC compliant components

Reference

Orangebox Campers & Dens – Assembly Instructions
Doc #170491 – Revision B
© 2024 Steelcase Inc.

This Zendesk article is an installation overview and does not replace the official assembly manual.